Step-Up Supply Charges Battery
the circuit of figure 1 supports the many portable applications in which a microprocessor (µp) or microcontroller (µc) controls charging of the battery. ic1 is a step-up switching regulator that boosts vin (nominally 5v) as necessary to supply the combination of charging current and load current. the 5v source must include short-circuit protection. ic2 is a high-side current-sense amplifier that monitors the charging current. commands from the processor include charge active-low on/off and active-low fast/trickle charge.
figure 1. this circuit controls charging of the battery while delivering current to the system load.
ic2 produces an output current (out) equal to 10-4 of the current through sense resistor r9. q3 and q4 are on during a fast-charge operation, so this output current flows through the parallel combination of r11 and (approximately) r4. the resulting feedback to ic1 (pin 3) maintains the fast-charge current through r9 at 500ma. this feedback also enables the regulator to supply as much as 500ma of load current in addition to the fixed 500ma of charging current. q2 limits the battery voltage to 10v (2v/cell).
during the fast charge, an external processor and multi-channel a/d converter (adc) must monitor the battery's terminal voltage. when the adc senses a change of slope in this voltage, the processor terminates the fast charge by asserting a high on active-low fast/ trickle charge. q3 turns off, causing a rise in the feedback (fb) that lowers the charging current to the trickle-charge rate (approximately 60ma).
if ic1 shuts down, or if load current plus charging current exceeds the capability of ic1, the r9 current reverses as current flows out of the battery. ic2 indicates the reversal by allowing r13 to pull its open-collector sign output high, turning off q4 and turning on q5. current through r12 then produces a voltage proportional to the battery's discharge current (5a through r9 produces a full-scale response of 3v across r12).
by integrating this voltage over time (sampling at fixed intervals and multiplying by the time interval), the a/d-processor system can monitor energy removed from the battery. based on this measurement and the terminal-voltage measurement, the processor can then re-initiate a fast charge (by asserting active-low fast/trickle charge low) before the battery reaches its end of life.
a related idea appeared in the 6/8/95 issue of edn.
有源功率因数校正技术及发展趋势
人类再次发现引力波 来自黑洞碰撞
基于ARM和CPLD的温度控制器的设计
华为鸿蒙系统蓄势待发 安卓系统必首先受到冲击
京东方、天马、惠科面板厂商将亮相DISPLAY CHINA 2019
Step-Up Supply Charges Battery
ams与ST联合发布同类产品最优安全NFC移动支付交易解决方案
5G的到来将如何影响边缘计算网络
AI在大流行期间所开展活动的广度
复合凝胶电解质中无机填料助力锂金属电池富无机物SEI的形成
DeepMind提出了可微分归纳逻辑编程方法∂ILP并进行解读
黑鲨游戏手机2怎么样 值不值得买
空气产品公司中国区总裁被任命为陕西省政府国际高级经济顾问
电源模块是什么？电源模块噪音过大的原因及解决办法
运动控制器哪家好_全球十大运动控制器品牌排行版
库克感叹iPhone 11夜拍给力，Deep Fusion功能的好处
Endura MEMS振荡器在极端条件下提供高可靠性和稳定性
京瓷株式会社选择Atmel maXTouch控制器助力其智能手机设计
激光加工技术加速了钣金车间生产自动化的进程
生活家健康指南：手机开机充电时切忌接打电话
figure 1. this circuit controls charging of the battery while delivering current to the system load.
ic2 produces an output current (out) equal to 10-4 of the current through sense resistor r9. q3 and q4 are on during a fast-charge operation, so this output current flows through the parallel combination of r11 and (approximately) r4. the resulting feedback to ic1 (pin 3) maintains the fast-charge current through r9 at 500ma. this feedback also enables the regulator to supply as much as 500ma of load current in addition to the fixed 500ma of charging current. q2 limits the battery voltage to 10v (2v/cell).
during the fast charge, an external processor and multi-channel a/d converter (adc) must monitor the battery's terminal voltage. when the adc senses a change of slope in this voltage, the processor terminates the fast charge by asserting a high on active-low fast/ trickle charge. q3 turns off, causing a rise in the feedback (fb) that lowers the charging current to the trickle-charge rate (approximately 60ma).
if ic1 shuts down, or if load current plus charging current exceeds the capability of ic1, the r9 current reverses as current flows out of the battery. ic2 indicates the reversal by allowing r13 to pull its open-collector sign output high, turning off q4 and turning on q5. current through r12 then produces a voltage proportional to the battery's discharge current (5a through r9 produces a full-scale response of 3v across r12).
by integrating this voltage over time (sampling at fixed intervals and multiplying by the time interval), the a/d-processor system can monitor energy removed from the battery. based on this measurement and the terminal-voltage measurement, the processor can then re-initiate a fast charge (by asserting active-low fast/trickle charge low) before the battery reaches its end of life.
a related idea appeared in the 6/8/95 issue of edn.
有源功率因数校正技术及发展趋势
人类再次发现引力波 来自黑洞碰撞
基于ARM和CPLD的温度控制器的设计
华为鸿蒙系统蓄势待发 安卓系统必首先受到冲击
京东方、天马、惠科面板厂商将亮相DISPLAY CHINA 2019
Step-Up Supply Charges Battery
ams与ST联合发布同类产品最优安全NFC移动支付交易解决方案
5G的到来将如何影响边缘计算网络
AI在大流行期间所开展活动的广度
复合凝胶电解质中无机填料助力锂金属电池富无机物SEI的形成
DeepMind提出了可微分归纳逻辑编程方法∂ILP并进行解读
黑鲨游戏手机2怎么样 值不值得买
空气产品公司中国区总裁被任命为陕西省政府国际高级经济顾问
电源模块是什么？电源模块噪音过大的原因及解决办法
运动控制器哪家好_全球十大运动控制器品牌排行版
库克感叹iPhone 11夜拍给力，Deep Fusion功能的好处
Endura MEMS振荡器在极端条件下提供高可靠性和稳定性
京瓷株式会社选择Atmel maXTouch控制器助力其智能手机设计
激光加工技术加速了钣金车间生产自动化的进程
生活家健康指南：手机开机充电时切忌接打电话