Step-up Converter with LDO Bea
abstract: a step-up converter followed by an ldo regulator offers better battery life than a classic sepic design when operating from one lithium-ion cell. this is demonstrated with the max1800 multi-channel digital camera power ic for the step-up plus ldo design and a max668 for the sepic design.
additional information: quick view data sheet for the max668/max669
samples and literature order form
technical support: powerthe use of lithium-ion batteries to power portable devices has become commonplace recently. one of the main drawbacks of using a lithium-ion battery is that a step-up/step-down dc/dc converter must be used to make the standard 3.3v power-supply voltage. this is so because the battery voltage typically ranges between 2.7v and 4.2v, overlapping the 3.3v output voltage requirement.
there are a few different topologies that can be used for a step-up/step-down converter, the most popular being the single-ended primary inductance converter (sepic). another option that is frequently overlooked is the step-up converter followed by a low dropout (ldo) regulator. because a linear regulator is used for the step-down function, it is often assumed that the efficiency is poor. however, when making 3.3v from a single lithium-ion battery, the efficiency of this circuit can exceed that of an equivalent sepic circuit, with the added benefit of lower cost and less board space.
figure 1 shows a portion of the max1800 five-channel step-up converter. the max1800 includes one synchronous rectified step-up converter, three step-up converter controllers, and a linear regulator controller. in this example, only the synchronous rectified step-up converter and linear regulator are discussed; however, it also applies to similar parts such as the max1703, the max1705, and the max1706.
figure 1. max1800 step-up/step-down circuit schematic.
the efficiency of this circuit versus load current over the typical lithium-ion battery range is shown in figure 2. as expected, the efficiency at 4.2v is poor due to the loss through the ldo regulator.
figure 2. max1800 step-up/step-down efficiency.
the equivalent sepic circuit is shown in figure 3. it uses the max668 step-up controller to make a sepic circuit. this circuit is more complex than the max1800 circuit shown above; however, more importantly, it requires either a single coupled inductor (transformer) or two separate inductors as well as a coupling capacitor. in the circuit shown, a coupled inductor is used.
figure 3. max668 sepic converter schematic.
the efficiency of this sepic circuit is shown in figure 4. the efficiency of the sepic circuit in step-up mode is lower than that of the step-up +ldo circuit of the max1800, whereas the efficiency with a 4.2v input is higher.
figure 4. max668 sepic converter efficiency.
to determine which circuit will result in longer battery life, the 1c discharge curve of a typical lithium-ion cell, the sony us18650, is used to weigh the efficiency curves with the amount of time that the battery will spend at that particular battery voltage. the discharge curve of the battery is shown in figure 5, and the weighing factors are shown in table 1.
figure 5. us18650 battery 1c discharge curve.
table 1. battery voltage weighing factors
battery voltage % of battery life
4.2v 8.6%
3.6v 64.3%
3.3v 12.1%
3.0v 10.7%
2.7v 4.3%
a composite efficiency curve using the data above and the weighing factors for input voltage is shown below. it can be seen that the peak efficiency of the step-up + ldo circuit exceeds that of the sepic, except for low currents.
figure 6. composite efficiency of the max1800 and the sepic versus load current.
the efficiency of a step-up converter followed by an ldo regulator is typically considered an unsatisfactory option due to the perception of poor efficiency from the ldo. however, this perception is incorrect in the case where the typical battery voltage is near the regulated output voltage, as occurs when generating 3.3v from a single lithium-ion battery. switching from a sepic circuit to a step-up + ldo circuit improves efficiency while also reducing the size and cost, making it clearly the better solution.
致远微电子首款多媒体控制和图像显示应用的高集成度芯片
汽车ECU诊断：车外离线诊断系统
耐威科技拟在青岛投资建设氮化镓晶圆制造项目 利于公司在第三代半导体领域的全产业链布局
霍尔效应传感技术优势有哪些
我们有必要过度担心指纹识别的风险吗
Step-up Converter with LDO Bea
英创信息技术RS485总线的特征简介与实际应用
模电放大电路的放大倍数怎么求？
数字信号处理第4部分—在MATLAB中创建GUI
第一款采用AD107小核心的桌面显卡RTX 4060
RT-Thread BSP v1.3.0 发布
AMD在桌面处理器以及服务器市场上正在给英特尔带来更大的麻烦
声音传感器工作原理
OpenCV中YAML配置文件读写使用演示
Exact应邀参展首届中国集成电路设计创新大会暨IC应用博览会并做主题演讲
变频器在络筒机上的应用
ES-BRIDGE2——MCU应用开发者的好帮手
区块链切入供应链金融，需要如下步骤
薄型微型压接连接器和配件介绍
DisplayPort端口到VGA转换器CS5212介绍
additional information: quick view data sheet for the max668/max669
samples and literature order form
technical support: powerthe use of lithium-ion batteries to power portable devices has become commonplace recently. one of the main drawbacks of using a lithium-ion battery is that a step-up/step-down dc/dc converter must be used to make the standard 3.3v power-supply voltage. this is so because the battery voltage typically ranges between 2.7v and 4.2v, overlapping the 3.3v output voltage requirement.
there are a few different topologies that can be used for a step-up/step-down converter, the most popular being the single-ended primary inductance converter (sepic). another option that is frequently overlooked is the step-up converter followed by a low dropout (ldo) regulator. because a linear regulator is used for the step-down function, it is often assumed that the efficiency is poor. however, when making 3.3v from a single lithium-ion battery, the efficiency of this circuit can exceed that of an equivalent sepic circuit, with the added benefit of lower cost and less board space.
figure 1 shows a portion of the max1800 five-channel step-up converter. the max1800 includes one synchronous rectified step-up converter, three step-up converter controllers, and a linear regulator controller. in this example, only the synchronous rectified step-up converter and linear regulator are discussed; however, it also applies to similar parts such as the max1703, the max1705, and the max1706.
figure 1. max1800 step-up/step-down circuit schematic.
the efficiency of this circuit versus load current over the typical lithium-ion battery range is shown in figure 2. as expected, the efficiency at 4.2v is poor due to the loss through the ldo regulator.
figure 2. max1800 step-up/step-down efficiency.
the equivalent sepic circuit is shown in figure 3. it uses the max668 step-up controller to make a sepic circuit. this circuit is more complex than the max1800 circuit shown above; however, more importantly, it requires either a single coupled inductor (transformer) or two separate inductors as well as a coupling capacitor. in the circuit shown, a coupled inductor is used.
figure 3. max668 sepic converter schematic.
the efficiency of this sepic circuit is shown in figure 4. the efficiency of the sepic circuit in step-up mode is lower than that of the step-up +ldo circuit of the max1800, whereas the efficiency with a 4.2v input is higher.
figure 4. max668 sepic converter efficiency.
to determine which circuit will result in longer battery life, the 1c discharge curve of a typical lithium-ion cell, the sony us18650, is used to weigh the efficiency curves with the amount of time that the battery will spend at that particular battery voltage. the discharge curve of the battery is shown in figure 5, and the weighing factors are shown in table 1.
figure 5. us18650 battery 1c discharge curve.
table 1. battery voltage weighing factors
battery voltage % of battery life
4.2v 8.6%
3.6v 64.3%
3.3v 12.1%
3.0v 10.7%
2.7v 4.3%
a composite efficiency curve using the data above and the weighing factors for input voltage is shown below. it can be seen that the peak efficiency of the step-up + ldo circuit exceeds that of the sepic, except for low currents.
figure 6. composite efficiency of the max1800 and the sepic versus load current.
the efficiency of a step-up converter followed by an ldo regulator is typically considered an unsatisfactory option due to the perception of poor efficiency from the ldo. however, this perception is incorrect in the case where the typical battery voltage is near the regulated output voltage, as occurs when generating 3.3v from a single lithium-ion battery. switching from a sepic circuit to a step-up + ldo circuit improves efficiency while also reducing the size and cost, making it clearly the better solution.
致远微电子首款多媒体控制和图像显示应用的高集成度芯片
汽车ECU诊断：车外离线诊断系统
耐威科技拟在青岛投资建设氮化镓晶圆制造项目 利于公司在第三代半导体领域的全产业链布局
霍尔效应传感技术优势有哪些
我们有必要过度担心指纹识别的风险吗
Step-up Converter with LDO Bea
英创信息技术RS485总线的特征简介与实际应用
模电放大电路的放大倍数怎么求？
数字信号处理第4部分—在MATLAB中创建GUI
第一款采用AD107小核心的桌面显卡RTX 4060
RT-Thread BSP v1.3.0 发布
AMD在桌面处理器以及服务器市场上正在给英特尔带来更大的麻烦
声音传感器工作原理
OpenCV中YAML配置文件读写使用演示
Exact应邀参展首届中国集成电路设计创新大会暨IC应用博览会并做主题演讲
变频器在络筒机上的应用
ES-BRIDGE2——MCU应用开发者的好帮手
区块链切入供应链金融，需要如下步骤
薄型微型压接连接器和配件介绍
DisplayPort端口到VGA转换器CS5212介绍