分立元件组成的烙铁电路
分立元件组成的烙铁电路
wattage of load
10w
18w
25w
35w
65w
80w
value of r5 (in ohms)
330
180
136 (68+68)
100
56
44 (22+22)
wattage of r5 (in watts)
01
02
02
04
05
6.5
usually a soldering iron takes a couple of minutes to get adequately heated up to melt the solder, after which the heat generated is much above the requirement and is wasted. moreover, excessive heat decreases the life of the bit and the element, causing serious damage to the components.
the above circuit solves this problem in a simple and inexpensive way and could be used to various types of loads up to 80watts.
how it works
once the main is switched on, an approximate 15v drop of the positive half cycle across r5 is detected and supplied to q1 (sl100 or d313), which acts as a voltage regulator. zener diode d2 together with diode d3 (yellow led) stabilizes the emitter voltage of q1 at 13.2vdc, which is then delivered to the relay circuit built around q2 and c3. capacitor c3 charges through the base-emitter path of q2 and causes the relay to actuate, which in turn allows both the half cycles of the ac mains to flow through diode d6 and r5 to the load to heat it up at a normal rate.
after a certain lapse of time (about 2 minutes preset) c3 saturates and q2 stops conducting through the relay, thus switching on series diode d5 to allow only half of the ac cycle through the load.
after switching off the system, c3 discharges very slowly through r2 and r3. before c3 gets completely discharged, if the power is switched on again, c3 takes a shorter time to reach the saturation level, thus switching series diode d5 much earlier than the preset time to prevent double heating of the load.
however, if the circuit is switched on only after a few seconds of switching off, c3 gets no time to discharge and the relay does not actuate at all. moreover, if the relay circuit fails due to any reason and q2 does not conduct, no harm is done to the load because in that case d5 remains in series with it. thus the circuit offers complete protection to the load.
as stated earlier, the given value of c3 gives a delay of 2 minutes. however, a 1000mfd capacitor can also be used to produce a 4.5-minute delay. r5 maintains a drop of about 15v across itself. so for use in different load conditions its value changes as shown in table 1.
the whole circuit can be mounted on a pcb and fitted in an adapter case (7.6cm x 5.1cm x 6.4cm) and used as a mains plug. since r5 gets heated up during the operation, it should be kept well isolated from the other components.
components list
r1 - 220 ohms
r2 – 10k
r3 – 150k
r4 – 82k
(all resistors should be 5% close tolerance)
c1- 100 uf, 25v dc working electrolytic
c2 – 100 uf, 25v dc working electrolytic
c3 – 220 uf, 16v dc working electrolytic
(advisable to use close tolerance caps. to obtain correct timings)
d1, d4, d5, & d6 – in4007
d2 – 12v 400mw, zener diode
d3 – yellow led
rly1 – 6v, 300 ohms dc relay
q1 – sl100 or d313
q2 – bc108
人工智能已成产业变革基石 千亿级市场盛宴将开启
逆变器过压保护介绍
可调参考电压源：Adjustable Voltage Ref
正确认识 PC-Based 逻辑分析仪
北京2025年超前布局6G等前沿技术，开展5G超高清视频典型场景的示范应
分立元件组成的烙铁电路
莱姆电子50周年丨跨越半个世纪的匠心精神，与工业相生相成
浙江省2002年7月高等教育自学考试计算机组成原理试题
华为最美颜值最高的手机，秒杀oppo和vivo，不夸张！
怎样将手电筒转换成灯笼
富勒G900S纯享版机械键盘评测 性价比还是相当高的
我国5G基站建设数量处于全球领先的地位，地级市以上已基本覆盖
实录光电科技U-DAT无人机数字化分析测试系统解读
我国建成世界首个民用电磁波发射台；中芯国际12nm开始客户导入
面对全球AI大模型的追赶 科大讯飞AI如何弯道超车
什么蓝牙耳机性价比高？四款性价比高的蓝牙耳机推荐
富士通推出带9KB FRAM的高频RFID标签芯片-MB89R112
基于物联网的家庭生活一天会是什么体验
准固定频率滞环PWM电流模式控制方法的研究
B站泰国版上架Google Play应用商店
wattage of load
10w
18w
25w
35w
65w
80w
value of r5 (in ohms)
330
180
136 (68+68)
100
56
44 (22+22)
wattage of r5 (in watts)
01
02
02
04
05
6.5
usually a soldering iron takes a couple of minutes to get adequately heated up to melt the solder, after which the heat generated is much above the requirement and is wasted. moreover, excessive heat decreases the life of the bit and the element, causing serious damage to the components.
the above circuit solves this problem in a simple and inexpensive way and could be used to various types of loads up to 80watts.
how it works
once the main is switched on, an approximate 15v drop of the positive half cycle across r5 is detected and supplied to q1 (sl100 or d313), which acts as a voltage regulator. zener diode d2 together with diode d3 (yellow led) stabilizes the emitter voltage of q1 at 13.2vdc, which is then delivered to the relay circuit built around q2 and c3. capacitor c3 charges through the base-emitter path of q2 and causes the relay to actuate, which in turn allows both the half cycles of the ac mains to flow through diode d6 and r5 to the load to heat it up at a normal rate.
after a certain lapse of time (about 2 minutes preset) c3 saturates and q2 stops conducting through the relay, thus switching on series diode d5 to allow only half of the ac cycle through the load.
after switching off the system, c3 discharges very slowly through r2 and r3. before c3 gets completely discharged, if the power is switched on again, c3 takes a shorter time to reach the saturation level, thus switching series diode d5 much earlier than the preset time to prevent double heating of the load.
however, if the circuit is switched on only after a few seconds of switching off, c3 gets no time to discharge and the relay does not actuate at all. moreover, if the relay circuit fails due to any reason and q2 does not conduct, no harm is done to the load because in that case d5 remains in series with it. thus the circuit offers complete protection to the load.
as stated earlier, the given value of c3 gives a delay of 2 minutes. however, a 1000mfd capacitor can also be used to produce a 4.5-minute delay. r5 maintains a drop of about 15v across itself. so for use in different load conditions its value changes as shown in table 1.
the whole circuit can be mounted on a pcb and fitted in an adapter case (7.6cm x 5.1cm x 6.4cm) and used as a mains plug. since r5 gets heated up during the operation, it should be kept well isolated from the other components.
components list
r1 - 220 ohms
r2 – 10k
r3 – 150k
r4 – 82k
(all resistors should be 5% close tolerance)
c1- 100 uf, 25v dc working electrolytic
c2 – 100 uf, 25v dc working electrolytic
c3 – 220 uf, 16v dc working electrolytic
(advisable to use close tolerance caps. to obtain correct timings)
d1, d4, d5, & d6 – in4007
d2 – 12v 400mw, zener diode
d3 – yellow led
rly1 – 6v, 300 ohms dc relay
q1 – sl100 or d313
q2 – bc108
人工智能已成产业变革基石 千亿级市场盛宴将开启
逆变器过压保护介绍
可调参考电压源：Adjustable Voltage Ref
正确认识 PC-Based 逻辑分析仪
北京2025年超前布局6G等前沿技术，开展5G超高清视频典型场景的示范应
分立元件组成的烙铁电路
莱姆电子50周年丨跨越半个世纪的匠心精神，与工业相生相成
浙江省2002年7月高等教育自学考试计算机组成原理试题
华为最美颜值最高的手机，秒杀oppo和vivo，不夸张！
怎样将手电筒转换成灯笼
富勒G900S纯享版机械键盘评测 性价比还是相当高的
我国5G基站建设数量处于全球领先的地位，地级市以上已基本覆盖
实录光电科技U-DAT无人机数字化分析测试系统解读
我国建成世界首个民用电磁波发射台；中芯国际12nm开始客户导入
面对全球AI大模型的追赶 科大讯飞AI如何弯道超车
什么蓝牙耳机性价比高？四款性价比高的蓝牙耳机推荐
富士通推出带9KB FRAM的高频RFID标签芯片-MB89R112
基于物联网的家庭生活一天会是什么体验
准固定频率滞环PWM电流模式控制方法的研究
B站泰国版上架Google Play应用商店