基于PCM2702的USB声卡原理图及电路图
基于pcm2702的usb声卡原理图及电路图
make a sound card is no more a complex issue. if you use great ic pcm2702 from burr brown / texas instruments you can create a fully functional usb sound card. this sound card can be powered from usb port and has one stereo output. you don’t need to install any driver for windows xp and vista, because they are already inside. this is really plug and play.
few months ago i have seen usb sound card called alien dac. the construction on the project web page inspired me to build this thing also.
the core of this construction is 16-bit stereo digital-to-analog convertor with usb interface pcm2702.
pcm2702 needs only few additional parts to work. the schematic is not complex. sound card can be powered directly from usb port (jumper w1) or from external power supply (jumper w3). pcm2702 needs two power supply 3.3v (3v-3.6v) and 5v (4.5v-5.5v). i used fixed output voltage ldo tps76733q for 3.3v (io2) and adjustable output voltage ldo tps76701q for 5v (io3). both ldo are produced by ti, i used this because i had it in my drawer. any similar ldo can be used. output voltage of io3 should be set to little bit lower than input voltage to allow ldo good stabilization, in my case output voltage is set to 4.8v. output voltage can be set by adjustable resistor r33. in case of low power supply, io3 can be shorted by jumper w3. led d3 signalizes power on.
small ferrite beads are placed before all power pins of pcm2702 and in vbus and gnd of usb. these small beads reduce high frequency hum. i had a problem find this small smd ferrite beads in local stores but finally i acquire few of them from old hard drive. they are not absolutely necessary, you can use zero ohm resistors instead of them.
low-pass filter is placed in output signal path to reduce sampling frequency. an opa2353ua dual op amp is configured as a stereo 2nd-order low-pass filter. led diode d1 is illuminated when pcm2702 plays audio data received from the usb bus. led diode d2 is illuminated when usb bus suspends audio data transmission to the pcm2702.
pcb图：
pcb assembly diagram
pcb - download pcb in [eps format] or [pdf format]
bottom side of pcb (single side pcb, made by standard etching method)
assembled bottom side
conclusion
this circuit works very well. i only shorted crystal during soldering so the circuit didn’t work, but after removing the short the sound card started to work. i have tested in windows 2000, xp and vista. it works in all mentioned systems. drivers are present in operation system so the sound card is ready in few seconds after you connect it.
during writing this article i have found that pcm2702 is now not recommended for new design, but ti offer even better solution. pcm2704, pcm2705 have same functionality as pcm2702, but they include output filter. they are able to drive directly headphones. volume and mute can be controlled through spi bus in pcm2705 or with pushbuttons in case of pcm2704. pcm2704 and pcm2705 are in tssop28 package. pcm2706 is similar to pcm2704 and pcm2707 to pcm2705 but in addition they have i2s bus. pcm2706 and pcm2707 are in tqfp32 package. i recommend using these new chips for new design (look at the ti web page).
如何设计校园电气建设节约型校园？
Logical Clocks宣布正在为AI-NET ANIARA项目开发第一个边缘计算企业功能商店
打铁还需自身硬，传感器融合算法还需要MEMS的高精度
中文语音合成芯片推荐
依图科技首次公开发行存托凭证并在科创板上市申请已获受理
基于PCM2702的USB声卡原理图及电路图
多功能警用电击充电装置制作
消费类电子产品多彩背光LED灯的设计方法
中国移动推出了聚合互联网优质资源满足用户的切实需求
一体式微型气象站气象传感器
如何制作一个定制数字手表
单相配电变压器的应用
华为携手湖南移动全力支撑华菱湘钢打造智慧湘钢
一个与材料行业人士讨论行业发展，查看行业动态，与行业人士交流的APP
黑盒测试的7种测试方法
5G技术浪潮对媒介产业发展有何影响?
FPGA在大数据时代的机遇与挑战
Intel9代酷睿新品公布报价 最低售价188美元
简述调制解调器在连网中的功能
华硕ACRH17路由器评测 简单便捷散热良好
make a sound card is no more a complex issue. if you use great ic pcm2702 from burr brown / texas instruments you can create a fully functional usb sound card. this sound card can be powered from usb port and has one stereo output. you don’t need to install any driver for windows xp and vista, because they are already inside. this is really plug and play.
few months ago i have seen usb sound card called alien dac. the construction on the project web page inspired me to build this thing also.
the core of this construction is 16-bit stereo digital-to-analog convertor with usb interface pcm2702.
pcm2702 needs only few additional parts to work. the schematic is not complex. sound card can be powered directly from usb port (jumper w1) or from external power supply (jumper w3). pcm2702 needs two power supply 3.3v (3v-3.6v) and 5v (4.5v-5.5v). i used fixed output voltage ldo tps76733q for 3.3v (io2) and adjustable output voltage ldo tps76701q for 5v (io3). both ldo are produced by ti, i used this because i had it in my drawer. any similar ldo can be used. output voltage of io3 should be set to little bit lower than input voltage to allow ldo good stabilization, in my case output voltage is set to 4.8v. output voltage can be set by adjustable resistor r33. in case of low power supply, io3 can be shorted by jumper w3. led d3 signalizes power on.
small ferrite beads are placed before all power pins of pcm2702 and in vbus and gnd of usb. these small beads reduce high frequency hum. i had a problem find this small smd ferrite beads in local stores but finally i acquire few of them from old hard drive. they are not absolutely necessary, you can use zero ohm resistors instead of them.
low-pass filter is placed in output signal path to reduce sampling frequency. an opa2353ua dual op amp is configured as a stereo 2nd-order low-pass filter. led diode d1 is illuminated when pcm2702 plays audio data received from the usb bus. led diode d2 is illuminated when usb bus suspends audio data transmission to the pcm2702.
pcb图：
pcb assembly diagram
pcb - download pcb in [eps format] or [pdf format]
bottom side of pcb (single side pcb, made by standard etching method)
assembled bottom side
conclusion
this circuit works very well. i only shorted crystal during soldering so the circuit didn’t work, but after removing the short the sound card started to work. i have tested in windows 2000, xp and vista. it works in all mentioned systems. drivers are present in operation system so the sound card is ready in few seconds after you connect it.
during writing this article i have found that pcm2702 is now not recommended for new design, but ti offer even better solution. pcm2704, pcm2705 have same functionality as pcm2702, but they include output filter. they are able to drive directly headphones. volume and mute can be controlled through spi bus in pcm2705 or with pushbuttons in case of pcm2704. pcm2704 and pcm2705 are in tssop28 package. pcm2706 is similar to pcm2704 and pcm2707 to pcm2705 but in addition they have i2s bus. pcm2706 and pcm2707 are in tqfp32 package. i recommend using these new chips for new design (look at the ti web page).
如何设计校园电气建设节约型校园？
Logical Clocks宣布正在为AI-NET ANIARA项目开发第一个边缘计算企业功能商店
打铁还需自身硬，传感器融合算法还需要MEMS的高精度
中文语音合成芯片推荐
依图科技首次公开发行存托凭证并在科创板上市申请已获受理
基于PCM2702的USB声卡原理图及电路图
多功能警用电击充电装置制作
消费类电子产品多彩背光LED灯的设计方法
中国移动推出了聚合互联网优质资源满足用户的切实需求
一体式微型气象站气象传感器
如何制作一个定制数字手表
单相配电变压器的应用
华为携手湖南移动全力支撑华菱湘钢打造智慧湘钢
一个与材料行业人士讨论行业发展，查看行业动态，与行业人士交流的APP
黑盒测试的7种测试方法
5G技术浪潮对媒介产业发展有何影响?
FPGA在大数据时代的机遇与挑战
Intel9代酷睿新品公布报价 最低售价188美元
简述调制解调器在连网中的功能
华硕ACRH17路由器评测 简单便捷散热良好