制作12db圆筒天线的方法及公式
圆筒天线的制作
we chose to build the antenna for 2.442ghz, or channel 7, as this is close to the center of the 13 channels available to us (us designs use channel 6 (2.437ghz), as they have 11 channels). i have included a key lengths calculator in the form below. nb.rectangular waveguides use a different formulae (see rectangular waveguide).
frequency频率
b/g chnl 1 b/g chnl 2 b/g chnl 3 b/g chnl 4 b/g chnl 5 b/g chnl 6 b/g chnl 7 b/g chnl 8 b/g chnl 9 b/g chnl 10 b/g chnl 11 b/g chnl 12 b/g chnl 13 b/g chnl 14 a chnl 34 a chnl 36 a chnl 38 a chnl 40 a chnl 42 a chnl 44 a chnl 46 a chnl 48 a chnl 52 a chnl 56 a chnl 60 a chnl 64 a chnl 149 a chnl 153 a chnl 157 a chnl 161 ghz
diameter 直径 mm (inside measurement)
free space
wavelength mm
waveguide
wavelength mm
最大频率 ghz
最小频率 ghz
截止频率 ghz
probe length mm 探针长度
open end to probe mm (open end to probe center)
probe to reflector探针到圆筒后面反射体 mm (probe center to reflector)
inside length mm (reflector to opening)
the final product only needs to be accurate to about 1mm as this will only shift the frequency within the range of the 802.11 spectrum. a smaller cavity length will shift the frequency response to that slot to a higher channel. a longer slot cavity length will shift it down.
methods and madness
i measured to .1mm using vernier callipers, on the assumption that errors in cutting might bring that closer to the 1mm error mark. there are only one to make, and you can't go too wrong, i.e. the probe (n-socket) position.
misc notes
* the probe is a 2mm diameter copper wire soldered into an n-socket and cut to 31mm (1/4 free space wavelength, including the protruding bit of the n-socket).
* 探针采用的是2mm直径的铜线焊接在n接头的槽上。探针长度为31mm，包含n接头突起的部分。
* the n-socket is held down with nylon screws. if you use metal screws, use stainless steal ones and keep them short so they don't protrude into the cavity.
* water in the antenna, or spider and insects will be a problem. one suggestion is to seal around the edges of the reflector with silicone and cover the open end with a piece of plastic (microwave friendly and thin).
n-socket with 1/4 wavelength copper wire (including the length of the bit of the n-socket it is soldered into). this becomes the probe for the antenna.
小米5s和小米6有什么区别？小米5s和小米6评测对比：都是无孔式指纹，你选谁？
国产化压力传感器的艰难发展
iPhone8什么时候上市？苹果新机iPhone8的性能售价遭到曝光，肾又不好了！
iCourt旗下AlphaGPT引领中国律师进入AI检索时代
从不均匀性角度浅析AB实验
制作12db圆筒天线的方法及公式
电子陀螺仪工作原理与构造
浅析机器人行业的发展与模式及技术方向
东山精密以超高的效率完成盐城生产基地的建设与投产
苹果税从30％降至15％，此番自断财路究竟意欲何为
关于IoT对WiFi发展的分析和介绍
开关电源有哪些EMI整改？
百炼智能与富士康旗下钜亿科技成功举办战略合作签约仪式
杭州规划好人工智能“国家试验田” 构建人工智能创新发展的生态系统
意法半导体推出支持3D的机顶盒芯片STi7108
中科院自动化所王飞跃教授作大会报告
自动驾驶在寒冬中孕育希望 Deepfake现已成魔
【干货分享】示波器（ADC）的采样率怎么理解？
如何推进人工智能与教育现代化发展的深度融合
自制胆前级用电子管测试仪
we chose to build the antenna for 2.442ghz, or channel 7, as this is close to the center of the 13 channels available to us (us designs use channel 6 (2.437ghz), as they have 11 channels). i have included a key lengths calculator in the form below. nb.rectangular waveguides use a different formulae (see rectangular waveguide).
frequency频率
b/g chnl 1 b/g chnl 2 b/g chnl 3 b/g chnl 4 b/g chnl 5 b/g chnl 6 b/g chnl 7 b/g chnl 8 b/g chnl 9 b/g chnl 10 b/g chnl 11 b/g chnl 12 b/g chnl 13 b/g chnl 14 a chnl 34 a chnl 36 a chnl 38 a chnl 40 a chnl 42 a chnl 44 a chnl 46 a chnl 48 a chnl 52 a chnl 56 a chnl 60 a chnl 64 a chnl 149 a chnl 153 a chnl 157 a chnl 161 ghz
diameter 直径 mm (inside measurement)
free space
wavelength mm
waveguide
wavelength mm
最大频率 ghz
最小频率 ghz
截止频率 ghz
probe length mm 探针长度
open end to probe mm (open end to probe center)
probe to reflector探针到圆筒后面反射体 mm (probe center to reflector)
inside length mm (reflector to opening)
the final product only needs to be accurate to about 1mm as this will only shift the frequency within the range of the 802.11 spectrum. a smaller cavity length will shift the frequency response to that slot to a higher channel. a longer slot cavity length will shift it down.
methods and madness
i measured to .1mm using vernier callipers, on the assumption that errors in cutting might bring that closer to the 1mm error mark. there are only one to make, and you can't go too wrong, i.e. the probe (n-socket) position.
misc notes
* the probe is a 2mm diameter copper wire soldered into an n-socket and cut to 31mm (1/4 free space wavelength, including the protruding bit of the n-socket).
* 探针采用的是2mm直径的铜线焊接在n接头的槽上。探针长度为31mm，包含n接头突起的部分。
* the n-socket is held down with nylon screws. if you use metal screws, use stainless steal ones and keep them short so they don't protrude into the cavity.
* water in the antenna, or spider and insects will be a problem. one suggestion is to seal around the edges of the reflector with silicone and cover the open end with a piece of plastic (microwave friendly and thin).
n-socket with 1/4 wavelength copper wire (including the length of the bit of the n-socket it is soldered into). this becomes the probe for the antenna.
小米5s和小米6有什么区别？小米5s和小米6评测对比：都是无孔式指纹，你选谁？
国产化压力传感器的艰难发展
iPhone8什么时候上市？苹果新机iPhone8的性能售价遭到曝光，肾又不好了！
iCourt旗下AlphaGPT引领中国律师进入AI检索时代
从不均匀性角度浅析AB实验
制作12db圆筒天线的方法及公式
电子陀螺仪工作原理与构造
浅析机器人行业的发展与模式及技术方向
东山精密以超高的效率完成盐城生产基地的建设与投产
苹果税从30％降至15％，此番自断财路究竟意欲何为
关于IoT对WiFi发展的分析和介绍
开关电源有哪些EMI整改？
百炼智能与富士康旗下钜亿科技成功举办战略合作签约仪式
杭州规划好人工智能“国家试验田” 构建人工智能创新发展的生态系统
意法半导体推出支持3D的机顶盒芯片STi7108
中科院自动化所王飞跃教授作大会报告
自动驾驶在寒冬中孕育希望 Deepfake现已成魔
【干货分享】示波器（ADC）的采样率怎么理解？
如何推进人工智能与教育现代化发展的深度融合
自制胆前级用电子管测试仪